MIL-PRF-83446/16B
TABLE I. Electrical characteristics (initial) - Continued.
Test
Q
DC
Q min
Self
Inductance (µH)
Current
Incre-
Resistance
Freq-
(typ)
over
resonant
Dash
(max)
mental
At 25 °C
uency
number
(at L
L
frequency
mA
current
(MHz)
nom)
range
(min)
(max)
2/
3/
Min
Nom
Max
1/
MHz
ohms
30
8.00
12.00
16.00
25
35
2.5
16
3.4
50
40
31
10.00
15.00
20.00
25
35
2.5
14
3.5
43
37
32
11.00
16.50
22.00
25
35
2.5
12
4.0
43
36
33
15.00
22.50
30.00
25
35
2.5
11
4.5
40
32
34
18.00
27.00
36.00
25
35
2.5
10
5.0
40
31
35
23.00
35.00
47.00
25
35
2.5
6.5
5.7
39
29
36
28.00
42.00
56.00
25
35
2.5
6.3
7.0
35
28
37
34.00
51.00
68.00
25
35
2.5
6.2
8.0
30
26
38
37.00
56.00
75.00
25
35
2.5
5.9
9.0
30
25
39
43.00
65.00
86.00
25
35
2.5
5.6
10.0
28
23
40
50.00
75.00
100
25
35
2.5
5.3
12.0
27
20
41
60.00
90.00
120
20
30
0.79
4.4
14.0
25
20
42
75.00
112.5
150
20
30
0.79
4.0
18.0
22
20
43
235
353
470
20
30
0.79
2.1
30.0
16
16
44
340
510
680
20
30
0.79
2.1
35.0
15
15
45
500
750
1000
20
30
0.79
1.1
75.0
11
11
1/ Test frequency range 0.25 through 25 MHz: For electrical characteristics measurements, use the HP260-A
Q Meter, HP4342A, HP250B RX Meter, or equivalent with the TF-401 test fixture, or equivalent (see figure 2).
Fixture inductance (approximately 0.038 µH) and residual Q-meter inductance (approximately 0.01 µH) should be
subtracted from indicated inductance.
Test frequency range 25 through 200 MHz: For electrical characteristics measurements, use the HP190-A
Q Meter, HP260-A Q Meter, HP4342A, HP250B RX Meter, or equivalent with the TF-401 test fixture, or
Equivalent (see figure 2). Fixture inductance (approximately 0.009 µH) should be subtracted from
indicated inductance.
2/ Maximum current allowed is not to exceed the specified temperature rise.
3/ Applicable to ferrite core only.
TABLE II. Electrical characteristics (final).
Inspection
Allowable variation from initial measurements
group
Inductance
DC resistance
Self-resonant
Q
frequency
(Percent)
(Percent)
(Percent)
Qualification
inspection
±5
±(3% +.001 ohm)
Group II
-8
-10
±5
±(2% +.001 ohm)
Group IV
-10
-10
±2
Group V
---
-10
---
Conformance
inspection group C
±5
±(3% +.001 ohm)
Subgroup II
-8
-10
±5
±(3% +.001 ohm)
Subgroup IV
-8
-10
4
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business