MS18100E
TABLE I. Electrical characteristics (initial).
Dash number 1/ 2/ |
Type designation |
Superseded MS PIN |
Inductance (µH) |
Q (min) |
Test frequency (MHz) |
SRF min (MHz) |
DC resistance (ohms) |
Rated dc current (mA) |
-1 -2 -3 -4 -5 -6 -7 -8 -9 -21 -22 |
LT4K200 LT4K201 LT4K202 LT4K203 LT4K204 LT4K205 LT4K206 LT4K207 LT4K208 LT4K220 LT4K221 |
MS16226-1 MS16226-2 MS16226-3 MS16226-4 MS16226-5 MS16226-6 MS16226-7 MS16226-8 MS16226-9 MS16226-21 MS16226-22 |
0.47 ±20% 0.68 ±20% 1.00 ±10% 1.50 ±10% 2.20 ±10% 2.70 ±10% 3.30 ±10% 3.90 ±10% 4.70 ±10% 47 ±10% 56 ±10% |
50 50 50 40 40 40 40 40 40 15 15 |
25 25 25 7.9 7.9 7.9 7.9 7.9 7.9 2.5 2.5 |
250 215 180 145 120 108 95 90 80 8.5 8.3 |
.06 .10 .15 .28 .50 .70 1.40 1.50 1.80 5.9 6.4 |
1,800 1,400 1,150 850 625 525 370 350 325 200 175 |
1/ The dash number added to MS military standard number constitutes the MS PIN; for example MS18100-1.
2/ The former MS part numbers MS18100-10 through MS18100-20 and MS18100-23 through MS18100-42 have been superseded as follows:
MS18100-10 through MS18100-20 by MS14040-1 through MS14040-11, respectively,
MS18100-23 through MS18100-27 by MS14041-1 through MS14041-5, respectively, MS18100-28 through MS18100-32 by MS14042-1 through MS14042-5, respectively, MS18100-33 through MS18100-37 by MS14043-1 through MS14043-5, respectively, MS18100-38 through MS18100-42 by MS14044-1 through MS14044-5, respectively,
TABLE II. Electrical characteristics (final). 1/
Inspection group |
Allowable variation from Initial measurement |
Allowable percent from specified minimum value in electrical characteristics (initial) table |
||
Inductance (percent) |
DC resistance |
Self-resonant frequency |
Q |
|
Qualification inspection Group II Group III Group IV 2/ |
±2 ±5 ±5 |
--- ±(3% +.001 ohm) ±(2% +.001 ohm) |
--- -8 -10 |
-10 -10 -15 |
Conformance inspection group C Subgroup I Subgroup II 2/ Subgroup III |
±2 ±5 ±5 |
--- ±(2% +.001 ohm) ±(3% +.001 ohm) |
--- -10 -8 |
-10 -15 -10 |
1/ Test fixture allowance of +.01 µH shall be added to all change in inductance limits ±( _ percent +.01 µH).
2/ The polarizing voltage during the moisture resistance tests Is applied with the positive lead connected to the coil terminals tied together, and the negative lead connected to the metal strap.
3
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business